Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2132

Страница: 2132 / 2589

DTC B1342 [POWER LIFTGATE (PLG) SYSTEM]

DTC B1342 - DETECTION CONDITION POSSIBLE CAUSE CHART

DIAGNOSTIC PROCEDURE

DTC B1342 - DIAGNOSTIC PROCEDURE

DTC B241A [POWER LIFTGATE (PLG) SYSTEM]

DTC B241A - DETECTION CONDITION POSSIBLE CAUSE CHART

Disconnect the negative battery cable.

Disconnect the positive battery cable.

Disconnect the PLG control module
connector.

Inspect the wiring harness between PLG

control module terminal 1C (wiring
harness-side) and positive battery terminal

(wiring harness-side) for an open
circuit/short circuit to ground system.

Is the wiring harness normal?

Yes Repair or replace the wiring harness.

Go to the next step.

VERIFY CORRECTION COMPLETED

Reconnect the disconnected connector.

Clear the DTC.

Operate the PLG system.

Is DTC B1318 stored?

Yes

Replace the PLG control module.
(See

POWER LIFTGATE (PLG)

CONTROL MODULE
REMOVAL/INSTALLATION

DTC troubleshooting completed.

DTC B1342

PLG control module internal malfunction

DETECTION CONDITION

Malfunction in the PLG control module internal circuit

POSSIBLE CAUSE

Malfunction in the PLG control module internal circuit

STEP

INSPECTION

ACTION

VERIFY DTC

Clear the DTC.

Operate the PLG
system.

Is DTC B1342

stored?

Yes

Replace the PLG control module.
(See

POWER LIFTGATE (PLG) CONTROL MODULE

REMOVAL/INSTALLATION

DTC troubleshooting completed.

DTC B241A

Touch sensor circuit malfunction

DETECTION

A short circuit to ground in the PLG touch sensor (RH/LH) continues for 5 min or

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 11

«
...
2130
2131
2132
2133
2134
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды