Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2396

Страница: 2396 / 2589

PASSENGER SIDE

1. Measure the voltage at each terminal (other than terminals I).

If the voltage is not as specified in the Terminal Voltage Table, inspect the parts under "Inspection
item(s)" and related wiring harnesses.

2. Disconnect the negative battery cable.
3. If the system does not work properly even though the inspection items or related wiring harnesses do not

have any malfunction, replace the power window subswitch.

Fig. 23: Power Window Subswitch (Passenger Side) - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

VOLTAGE SPECIFICATION

Terminal Signal name

Connected

Measured

condition

Voltage (V)/

Continuity

Inspection item (s)

Communication

Power

window

main switch

Because this terminal is for

communication, good/no good

judgment by terminal voltage is

not possible.

Power window motor

(See

POWER

WINDOW MAIN

SWITCH
INSPECTION

Related wiring harnesses

Power supply

Power

window

motor

Ignition switch
at ON or during

IG-OFF timer

B+

Power window motor

(See

POWER

WINDOW MOTOR

INSPECTION

Related wiring harnesses

Close output

Power

window

motor

While door
glass is opening

1.0 or less

Power window motor
(See

POWER

WINDOW MOTOR
INSPECTION

While door

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 17

«
...
2394
2395
2396
2397
2398
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды