Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1815

Страница: 1815 / 2589

Fig. 5: Identifying Instrument Cluster Unit, Cover, Lens & Glass Ring

Courtesy of MAZDA MOTORS CORP.

2. Assemble in the reverse order of disassembly.

INSTRUMENT CLUSTER INSPECTION

SPEEDOMETER

Using the input/output check mode

1. Inspect the speedometer by setting it to check code 12 of the input/output check mode. (See

INSTRUMENT CLUSTER INPUT/OUTPUT CHECK MODE

Using a speedometer tester

1. Adjust the tire pressure to the specification.
2. Using a speedometer tester, verify that the tester reading is as indicated in the table below.

SPEEDOMETER TESTER INDICATION AND ALLOWABLE RANGE REFERENCE

Speedometer tester indication (km/h) Allowable range (km/h)

17-23

38-43

57-63

77-83

100

97-103

120

116-124

140

136-144

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:42:26 AM

Page 5

«
...
1813
1814
1815
1816
1817
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды