Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 316

Страница: 316 / 2589

Fig. 283: Cleaning Sealant And Oil Off Contact Surface Of Transaxle Case

Courtesy of MAZDA MOTORS CORP.

90. Apply sealant to the new control valve body cover as shown in the figure.

Fig. 284: Identifying Sealant On Control Valve Body Cover

Courtesy of MAZDA MOTORS CORP.

91. Install the new control valve body cover with new seal bolts.

Tightening torque 9.8 - 15.7 N.m {100 - 160 kgf.cm, 87 - 138 in.lbf}

CAUTION:

Be careful that the coupler component will not become caught

between the control valve body cover and transaxle case.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:17 AM

Page 153

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды