Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2198

Страница: 2198 / 2589

Fig. 2: Identifying Main Fuse Screw

Courtesy of MAZDA MOTORS CORP.

IGNITION SWITCH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the column cover. (See

COLUMN COVER REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.

Fig. 3: Identifying Ignition Switch Remove/Install Components

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

IGNITION SWITCH INSPECTION

1. Verify that the continuity between the ignition switch terminals is as indicated in the table.

If not as indicated in the table, replace the ignition switch.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Power Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:41:28 AM

Page 2

«
...
2196
2197
2198
2199
2200
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды