Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2092

Страница: 2092 / 2589

NO.5 NO VOICE NAVIGATION [CAR-NAVIGATION SYSTEM]

TROUBLESHOOTING CHART

DIAGNOSTIC PROCEDURE

Disconnect the GPS antenna connector.

Inspect both GPS antenna connector and

car-navigation unit connector for poor
connection (such as damaged/pulled-out

pins, corrosion).

Are all the pins normal?

If the wiring harness-side connector is

wrong:

Repair or replace the suspect wiring

harness.

If the car-navigation unit side connector is

wrong:

Replace the car-navigation unit. (See

CAR-NAVIGATION UNIT

REMOVAL/INSTALLATION

No voice navigation

POSSIBLE

CAUSE

Improper adjustment of the NAVI voice volume

Car-navigation unit malfunction

Poor connection of the driver-side front door speaker connector, terminal
damage

Driver-side front door speaker malfunction

Poor connection of the car-navigation unit connector, terminal damage

Open or short circuit in driver-side front door speaker wiring harness

Poor connection of the audio amplifier connector, terminal damage

STEP

INSPECTION

ACTION

Is the voice navigation volume mute?

Yes Go to the next step.
No

Turn on the voice navigation.

Turn the audio power switch (CD, MD,
radio) to ON.

Does the driver-side front door speaker

work?

Yes Go to step 7.

Go to the next step.

Turn the ignition switch to the LOCK
position.

Remove the driver-side front door

speaker. (See

FRONT DOOR

SPEAKER

Yes Go to the next step.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Symptom Troubleshooting (Car Navigation System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:44 AM

Page 11

«
...
2090
2091
2092
2093
2094
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды