Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2439

Страница: 2439 / 2589

WINDSHIELD WIPER ARM AND BLADE ADJUSTMENT

1. Operate the windshield wipers, and then turn off the windshield wiper motor to set the wipers in the park

position.

2. Slide the serrated connecting part and adjust the windshield wiper arm and blade so that its end is aligned

with the hollowed mark in the ceramic coating.

WINDSHIELD WIPER MOTOR REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the windshield wiper arm and blade. (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

3. Remove the cowl grille. (See

COWL GRILLE REMOVAL/INSTALLATION

4. Remove in the order indicated in the table.

NOTE:

If the hollowed mark in the ceramic coating cannot be located, measure

the distance from the cowl grille end line, and adjust the windshield wiper

arm and blade.

Fig. 4: Identifying Windshield Wiper Arm And Blade Adjusting
Dimensions

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:19 AM

Page 4

«
...
2437
2438
2439
2440
2441
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды