Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 581

Страница: 581 / 2589

1. Disconnect the negative battery cable.
2. Drain the engine coolant. (See

ENGINE COOLANT REPLACEMENT [MZI-3.7]

3. Remove the air cleaner and fresh air duct component. (See

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.7]

4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Refill the engine coolant. (See

ENGINE COOLANT REPLACEMENT [MZI-3.7]

7. Inspect for engine coolant leakage. (See

ENGINE COOLANT LEAKAGE INSPECTION [MZI-3.7]

Fig. 15: Identifying Thermostat Cover, Thermostat & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

THERMOSTAT INSTALLATION NOTE

1. Install the thermostat into the thermostat case with the jiggle pin at the top.

When you are sure all the pressure is gone, press down on the cap
using the cloth, turn it, and remove it.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Cooling System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:57:25 AM

Page 15

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды