Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 490

Страница: 490 / 2589

DTC C1329, C1330, C1331, C1332, C1333, C1334, C1335, C1336, C1527,

C1528, C1530, C1531 [DSC/RSC]

DTC C1329, C1330, C1331, C1332, C1333, C1334, C1335, C1336, C1527, C1528, C1530, C1531
[DSC/RSC] DETECTION CONDITION AND POSSIBLE CAUSE

DIAGNOSTIC PROCEDURE

DTC C1329, C1330, C1331, C1332, C1333, C1334, C1335, C1336, C1527, C1528, C1530, C1531

[DSC/RSC] DIAGNOSTIC PROCEDURE

Are any other DTCs present?

DTC troubleshooting completed.

DTC C1329

RF outlet solenoid valve coil system

DTC C1330

LR outlet solenoid valve coil system

DTC C1331

RR outlet solenoid valve coil system

DTC C1332

LF outlet solenoid valve coil system

DTC C1333

LR inlet solenoid valve coil system

DTC C1334

LF inlet solenoid valve coil system

DTC C1335

RF inlet solenoid valve coil system

DTC C1336

RR inlet solenoid valve coil system

DTC C1527

RH traction control solenoid valve coil system

DTC C1528

LH traction control solenoid valve coil system

DTC C1530

RH stability control solenoid valve coil system

DTC C1531

LH stability control solenoid valve coil system

DETECTION

CONDITION

Temperature of a solenoid valve coil exceeds specification.

POSSIBLE CAUSE

This does not indicate a malfunction since constant control over extended

period of time is inhibited to protect the RSC solenoid valve inside the
DSC/RSC HU.

STEP

INSPECTION

ACTION

VERIFY DTC TROUBLESHOOTING

COMPLETED

Clear the DTC from the memory.

(See

ON-BOARD DIAGNOSTIC

[DSC/RSC]

Are the same DTCs present?

Yes

Replace the DSC/RSC HU/CM, then go to the
next step.

(See

DSC/RSC HU/CM

REMOVAL/INSTALLATION

Go to the next step.

VERIFY AFTER REPAIR

PROCEDURE

Are any other DTCs present?

Yes

Go to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSTIC

[DSC/RSC]

DTC troubleshooting completed.

2008 Mazda CX-9 Grand Touring

2008 BRAKES On-Board Diagnostic (DSC/RSC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:13 AM

Page 34

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды