Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2426

Страница: 2426 / 2589

Fig. 68: Power Outer Mirror - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

2. Inspect for continuity between the power outer mirror heater terminals.

If not as specified, replace the power outer mirror.

Fig. 69: Power Outer Mirror Heater Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 70: Power Outer Mirror Heater - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

3. Verify that the continuity is as indicated in the table.

If not as indicated, replace the power outer mirror.

Right

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:17 AM

Page 47

«
...
2424
2425
2426
2427
2428
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды