Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 356

Страница: 356 / 2589

[AW6A-EL, AW6AX-EL]

13. Install the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

14. Connect the negative battery cable.
15. Perform the mechanical system test. (See

MECHANICAL SYSTEM TEST [AW6A-EL, AW6AX-

EL]

VEHICLE SPEED SENSOR (VSS) INSPECTION [AW6A-EL, AW6AX-EL]

ON-VEHICLE INSPECTION

1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION

[MZI-3.7]

3. Remove the TCM. (See

TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

4. Verify that there is no continuity between the coupler component terminals B19 and GND or B20 and

GND.

Fig. 28: Identifying Coupler Component

Courtesy of MAZDA MOTORS CORP.

If there is any malfunction, inspect the coupler component.

If the coupler component is normal, replace the ATX. (See

AUTOMATIC TRANSAXLE

REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

CAUTION:

Water or foreign material entering the connector can cause a poor
connection or corrosion. Be sure not to allow water or foreign

material on the connector when disconnecting.

Do not damage the terminals.

NOTE:

Inspect with a tester that can indicate more than 10 megohms
and confirm that the value is more than 1 megohm.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 28

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды