Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1702

Страница: 1702 / 2589

Fig. 37: Removing Pressure Plate

Courtesy of MAZDA MOTORS CORP.

3. Disassemble in the order indicated in the table.

Fig. 38: Identifying Pressure Plate Disassembly Order & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Assemble in the reverse order of disassembly.
5. Adjust the magnetic clutch clearance. (See

MAGNETIC CLUTCH ADJUSTMENT

SNAP RING INSTALLATION NOTE

1. Install the snap ring so that the tapered area is on the pressure plate side.

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:35 AM

Page 23

«
...
1700
1701
1702
1703
1704
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды