Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1566

Страница: 1566 / 2589

Fig. 29: Identifying Side Step Molding With Clips

Courtesy of MAZDA MOTORS CORP.

SIDE STEP MOLDING INSTALLATION

1. Install the clips A and B.
2. Return the over fender to its original position.

Fig. 30: Identifying Side Step Molding With Clips

Courtesy of MAZDA MOTORS CORP.

FRONT SASH MOLDING REMOVAL

1. Remove the power outer mirror. (See

POWER OUTER MIRROR REMOVAL/INSTALLATION

WARNING:

Using a razor with bare hands can cause injury. Always wear gloves
when using a razor.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Exterior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:03 AM

Page 21

«
...
1564
1565
1566
1567
1568
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды