Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1645

Страница: 1645 / 2589

Fig. 4: Fuel System Diagram

Courtesy of MAZDA MOTORS CORP.

BEFORE SERVICE PRECAUTION [MZI-3.7]

FUEL LINE SAFETY PROCEDURE

1. Remove the fuel-filler cap and release the pressure in the fuel tank.
2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [MZI-3.7]

3. Remove the fuel pump relay.
4. Connect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [MZI-3.7]

WARNING:

Fuel vapor is hazardous. It can easily ignite, causing serious injury

and damage. Always keep sparks and flames away from fuel.

Fuel line spills and leakage are dangerous. Fuel can ignite and cause

serious injuries or death and damage. Fuel can also irritate skin and
eyes. To prevent this, always complete the following "Fuel Line

Safety Procedure".

A person charged with static electricity could cause a fire or

explosion, resulting in death or serious injury. Before performing
work on the fuel system, discharge static electricity by touching the

vehicle body.

NOTE:

Fuel in the fuel system is under high pressure also when the engine is not

running.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Fuel System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:00:01 AM

Page 4

«
...
1643
1644
1645
1646
1647
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды