Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 725

Страница: 725 / 2589

Fig. 36: Identifying Brake Pipe & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

TCS OFF SWITCH REMOVAL/INSTALLATION

1. Remove the dashboard under cover (LH). (See

DASHBOARD REMOVAL/INSTALLATION

2. Remove the hood release lever. (See

HOOD LATCH AND RELEASE LEVER

REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.

Fig. 37: Identifying TCS OFF Switch & TCS OFF Switch Connector

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

TCS OFF SWITCH REMOVAL NOTE

1. Access the TCS OFF switch from behind of the dashboard, and squeeze the tabs of the switch.
2. Remove the TCS OFF switch from the dashboard.

TCS OFF SWITCH INSPECTION

1. Remove the TCS OFF switch. (See

TCS OFF SWITCH REMOVAL/INSTALLATION

2. Verify that the continuity is as indicated in the table.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 32

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды