Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 514

Страница: 514 / 2589

DSC/RSC RELATED PARTS

1. Make sure that there are no DTCs in the DSC/RSC memory after working on DSC/RSC related parts. If

there are any DTCs in the memory, clear them. (See

ON-BOARD DIAGNOSIS [DSC/RSC]

DSC/RSC RELATED PART SENSOR INITIALIZATION PROCEDURE

1. When replacing or removing the following parts, perform the initialization procedure. (See

DSC/RSC

SENSOR INITIALIZATION PROCEDURE

DSC/RSC HU/CM

Combined sensor

WARNING:

If the initialization procedure is not completed, the DSC/RSC will not

operate properly and it might cause an unexpected accident.
Therefore, when replacing or removing the following parts, make

sure to perform the initialization procedure to insure proper RSC
operation.

2008 Mazda CX-9 Grand Touring

2008 BRAKES General Procedures (Brakes) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:44:11 AM

Page 2

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды