Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1527

Страница: 1527 / 2589

If not as indicated in the table, replace the GPS antenna feeder.

Fig. 44: GPS Antenna Feeder Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 45: Identifying GPS Antenna Feeder Terminals

Courtesy of MAZDA MOTORS CORP.

GPS ANTENNA REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Front console box mat (See

FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION

2. Indicator panel (See

INDICATOR PANEL REMOVAL/INSTALLATION

3. Decoration panel (See

DECORATION PANEL REMOVAL/INSTALLATION

4. Front console box (See

FRONT CONSOLE BOX REMOVAL/INSTALLATION

5. Center panel (See

CENTER PANEL REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 27

«
...
1525
1526
1527
1528
1529
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды