background image

© 2012 American Honda Motor Co., Inc. - All Rights Reserved.

BII 47360 (1209)

1 of 6

08L07-TA1-1B00-91

INSTALLATION
INSTRUCTIONS

Accessory

Application

Publications No.

Issue Date

SEP 2012

2013 TSX

SPORT WAGON

PARTS LIST

Bike attachment

Allen wrench, 5 mm

2 Keys

2 Wheel straps

2 Tire adapters

BII 13472

BICYCLE ATTACHMENT

(ROOF MOUNT)

P/N 08L07-TA1-203

2 End caps

TOOLS REQUIRED

Phillips screwdriver

Before Installing and Using This Bicycle
Attachment Kit

If the bicycle attachment is not installed properly, it
may come out of position while the vehicle is in motion,
resulting in serious injury or accident.  Read these
instructions carefully before installing the bicycle
attachment.

INSTALLATION

NOTE:

Be careful not to damage the painted surfaces of the
vehicle when installing the bike attachment.

If you are installing more than one bike attachment,
you may need to alternate the mounting positions
(front to rear) to allow for handle bar clearance.

Make sure the security retainer and the locking clamp
lever are installed on the outboard side. See the
Owner's Manual supplied for details.

The crossbars have a directional positioning. The
short portion in front of the channel should face
toward the front of the vehicle.

These instructions show the bicycle attachment
being installed on the passenger’s side of the
vehicle; use the same procedure to install the
bicycle attachment on the driver's side of the
vehicle.

Содержание 08L07-TA1-203







Отзывы: