Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 405

Страница: 405 / 2589

8. Connect the solenoid connectors, VSS connector and the input/turbine speed sensor connector.

Fig. 105: Connecting Solenoid Connectors, VSS Connector & Input/Turbine Speed Sensor
Connector

Courtesy of MAZDA MOTORS CORP.

9. Connect the coupler component to the clamps.

10. Clean sealant and oil off the contact surface of the transaxle case with the control valve body cover and

the bolt holes.

11. Clean oil off the contact surface of the new control valve body cover with the transaxle case.

NOTE:

Completely remove sealant and oil with white gasoline or similar.

Fig. 106: Connecting Coupler Component To Clamps

Courtesy of MAZDA MOTORS CORP.

NOTE:

Completely remove oil with white gasoline or similar.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 77

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды