Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2163

Страница: 2163 / 2589

Disconnect the PLG control module

connector.

Disconnect the PLG drive unit

connector.

Inspect the wiring harness between
PLG control module terminals 21 and

2G, and PLG drive unit terminals M
and N for an open circuit.

Is the wiring harness normal?

Yes

Replace the PLG drive unit.

(See

POWER LIFTGATE (PLG) DRIVE

UNIT REMOVAL/INSTALLATION

Go to the next step.

Repair or replace the wiring harness.

Go to the next step.

VERIFY CORRECTION COMPLETED

Reconnect the disconnected connector.

Clear the DTC.

Operate the PLG system.

Is DTC B2939 stored?

Yes

Replace the PLG control module.
(See

POWER LIFTGATE (PLG)

CONTROL MODULE
REMOVAL/INSTALLATION

DTC troubleshooting completed.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 42

«
...
2161
2162
2163
2164
2165
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды