Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 639

Страница: 639 / 2589

POWER LIFTGATE (PLG) SLIDER REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Trunk box (See

TRUNK BOX REMOVAL/INSTALLATION

2. Seat side box (LH) (See

SEAT SIDE BOX REMOVAL/INSTALLATION

3. Trunk end trim (See

TRUNK END TRIM REMOVAL/INSTALLATION

4. Third-row seat (See

THIRD-ROW SEAT REMOVAL/INSTALLATION

5. Third-row seat belt lower anchor installation bolt (LH) (See

THIRD-ROW SEAT BELT

REMOVAL/INSTALLATION

6. Rear scuff plate inner (LH) (See

REAR SCUFF PLATE REMOVAL/INSTALLATION

7. Trunk side trim (LH) (See

TRUNK SIDE TRIM REMOVAL/INSTALLATION

8. Roof side trim (LH) (See

ROOF SIDE TRIM REMOVAL/INSTALLATION

9. Third-row seat belt upper anchor installation bolt (LH) (See

THIRD-ROW SEAT BELT

REMOVAL/INSTALLATION

10. D-pillar trim (LH) (See

D-PILLAR TRIM REMOVAL/INSTALLATION

3. Disconnect the connection of the band that is on the PLG slider side of PLG arm with using the flat blade

screwdriver.

4. Put the PLG arm.

Fig. 14: Prying PLG Arm Band With Screwdriver

Courtesy of MAZDA MOTORS CORP.

5. Revolve the outer joint in the direction of the arrow to disconnect from the PLG slider and the PLG drive

unit.

6. Remove the bolts.
7. Remove the PLG slider.

NOTE:

If the negative battery cable is disconnected with the liftgate half opened,

the clutch cannot be disengaged resulting in difficulty in opening/closing
operation of the liftgate. Disconnect the negative battery cable with the

liftgate in the fully open/close position.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Doors and Liftgate - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:45:23 AM

Page 13

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды