Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2251

Страница: 2251 / 2589

2. Jack up the rear suspension with unloaded condition.

3. Mark the rear upper arm and rear crossmember shown in the figure.
4. Remove the presilencer. (See

EXHAUST SYSTEM REMOVAL/INSTALLATION [MZI-3.7]

Fig. 48: Marking Rear Upper Arm And Rear Crossmember

Courtesy of MAZDA MOTORS CORP.

5. Remove the presilencer insulator.
6. Remove the propeller shaft. (See

PROPELLER SHAFT REMOVAL/INSTALLATION

7. Remove the rear ABS wheel-speed sensor. (See

REAR ABS WHEEL-SPEED SENSOR

REMOVAL/INSTALLATION [AWD]

8. Remove the rear coil spring. (See

REAR COIL SPRING REMOVAL/INSTALLATION

9. Remove in the order indicated in the table.

10. Install in the reverse order of removal.

Fig. 47: Supporting Jack Up Point For Front Crossmember

Courtesy of MAZDA MOTORS CORP.

NOTE:

Jacking up the rear suspension with unloaded condition will lighten

the force on the bushing and make it easier to perform the procedure.

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION Rear Suspension - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:24:02 AM

Page 32

«
...
2249
2250
2251
2252
2253
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды