Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2428

Страница: 2428 / 2589

Fig. 73: Blind Spot Monitoring Indicator Light - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

POWER OUTER MIRROR SWITCH REMOVAL/INSTALLATION

POWER OUTER MIRROR SWITCH INSPECTION

1. Inspect for continuity between the power outer mirror switch terminals using an ohmmeter.

If not as indicated in the table, replace the power outer mirror switch.

Fig. 74: Power Outer Mirror Switch Continuity Chart

Courtesy of MAZDA MOTORS CORP.

NOTE:

The power outer mirror switch is integrated with the power window main

switch.(See POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION)

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:17 AM

Page 49

«
...
2426
2427
2428
2429
2430
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды