Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1550 | Manualshive

Страница: 1550 / 2589

background image

Fig. 4: Identifying Cowl Grille, Windshield Washer Hose And Joint Pipe

Courtesy of MAZDA MOTORS CORP.

FRONT BELTLINE MOLDING REMOVAL/INSTALLATION

REMOVAL

1. Fully open the front door glass.
2. Disconnect the negative battery cable.
3. Remove the inner garnish. (See

INNER GARNISH REMOVAL/INSTALLATION

.)

4. Remove the front door trim. (See

FRONT DOOR TRIM REMOVAL/INSTALLATION

.)

5. Remove the power outer mirror. (See

POWER OUTER MIRROR REMOVAL/INSTALLATION

.)

6. Remove clip A using a protective tape-wrapped flathead screwdriver.
7. Lift (partially peeling back) the front beltline molding in the direction of the arrow and then remove tabs

B.

8. Remove the clip C.
9. Remove the front beltline molding.

Fig. 5: Identifying Front Beltline Molding With Clips And Tab

Courtesy of MAZDA MOTORS CORP.

INSTALLATION

1. Install the clip A.
2. Install the tabs B.
3. Install the clip C.
4. Install the front beltline molding.
5. Install the power outer mirror. (See

POWER OUTER MIRROR REMOVAL/INSTALLATION

.)

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Exterior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:03 AM

Page 5

© 2005 Mitchell Repair Information Company, LLC.

«
...
1548
1549
1550
1551
1552
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: RaceChip Страницы: 12

Бренд: Saab Страницы: 10

Reference Series

Бренд: OEM Audio Страницы: 29

Бренд: Yakima Страницы: 12

Бренд: Ford Страницы: 22

Бренд: Haibang Страницы: 6

Бренд: Mazda Страницы: 720

Бренд: Whispbar Страницы: 15

Бренд: Gatorback Mudflaps Страницы: 4

Бренд: Hyundai Страницы: 280

Бренд: Park-Daddy Страницы: 22

Бренд: EUFAB Страницы: 12

Бренд: Hyundai Страницы: 18

Бренд: Demco Страницы: 4

Бренд: Yakima Страницы: 15

PRIME DESIGN HXR-269-E-UM3-80

Бренд: Safe Fleet Страницы: 12

Quantum Wash'n'Wipe N30208

Бренд: National Cycle Страницы: 12

Бренд: TrailFX Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды