Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1721

Страница: 1721 / 2589

Temperature control
dial (driver side):

Set temperature at
MAX HOT

1.0

mix actuator

Front climate control

unit: terminal voltage
(2B)

Potentiometer
input

Passenger-side
front air mix

actuator

Temperature control

dial (passenger
side): Set

temperature at
MAX COLD

1.0

Wiring harness:
continuity, short circuit

(Front climate control
unit-passenger-side

front air mix actuator:
2G-E)

Passenger-side front

air mix actuator

Front climate control
unit: terminal voltage

(2B)

Temperature control
dial (passenger

side): Set
temperature at

MAX HOT

4.0

Front
evaporator

temperature
sensor input

Front evaporator

temperature sensor

Compared with

temperature
detected by front

evaporator

temperature sensor

Refer to

Wiring harness:
continuity (Front

climate control unit--
front evaporator

temperature sensor:
2H-B, 2P-A)

Wiring harness: short

circuit (Front climate
control unit-front

evaporator temperature
sensor: 2H-B)

Front evaporator

temperature sensor

Ambient
temperature

sensor input

Ambient
temperature sensor

Compared with

temperature
detected by ambient

temperature sensor

Refer to

Wiring harness:
continuity (Front

climate control unit-
ambient temperature

sensor: 21-B, 2P-A)

Wiring harness: short
circuit (Front climate

control unit-ambient
temperature sensor:

21-B)

Ambient temperature
sensor

Wiring harness:
continuity (Front

climate control unit-
rear evaporator

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:36 AM

Page 42

«
...
1719
1720
1721
1722
1723
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды