Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1978

Страница: 1978 / 2589

6. Install in the reverse order of removal.

Fig. 9: Identifying Inner Handle & Door Lock Knob

Courtesy of MAZDA MOTORS CORP.

REAR

1. Disconnect the negative battery cable.
2. Remove the inner sail garnish. (See

INNER SAIL GARNISH REMOVAL/INSTALLATION

3. Remove the rear door trim. (See

REAR DOOR TRIM REMOVAL/INSTALLATION

4. Detach the cables from the inner handle and door lock knob.
5. Install in the reverse order of removal.

Fig. 10: Identifying Inner Handle & Door Lock Knob

Courtesy of MAZDA MOTORS CORP.

HOOD LATCH & RELEASE LEVER REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Air cleaner (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-3.7]

2. Splash shield (LH) (See

SPLASH SHIELD REMOVAL/INSTALLATION

3. Dashboard under cover (Driver side) (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:58 AM

Page 8

«
...
1976
1977
1978
1979
1980
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды