Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2239

Страница: 2239 / 2589

1. Remove the presilencer. (See

EXHAUST SYSTEM REMOVAL/INSTALLATION [MZI-3.7]

2. Remove the presilencer insulator.
3. Remove the propeller shaft. (See

PROPELLER SHAFT REMOVAL/INSTALLATION

4. Remove the rear ABS wheel-speed sensor. (See

REAR ABS WHEEL-SPEED SENSOR

REMOVAL/INSTALLATION [AWD]

5. Remove the rear coil spring. (See

REAR COIL SPRING REMOVAL/INSTALLATION

6. Remove in the order indicated in the table.
7. Install in the reverse order of removal.

Fig. 31: Identifying Presilencer Insulator, Presilencer & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION Rear Suspension - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:24:02 AM

Page 20

«
...
2237
2238
2239
2240
2241
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды