Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1979

Страница: 1979 / 2589

3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. Adjust the hood. (See

HOOD ADJUSTMENT

Fig. 11: Identifying Hood Latch, Release Lever Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

HOOD RELEASE LEVER REMOVAL NOTE

1. Pull the lever.
2. Insert a tape-wrapped flathead screwdriver into the position shown in the figure.

3. Pull the hood release lever outward and remove it.

CAUTION:

Be careful not to damage the hood release cable when removing
the hood release lever with the flathead screwdriver.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:58 AM

Page 9

«
...
1977
1978
1979
1980
1981
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды