Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1590

Страница: 1590 / 2589

Fig. 9: Installing Upper Spring Seat

Courtesy of MAZDA MOTORS CORP.

MOUNTING RUBBER ASSEMBLY NOTE

1. Slide the mounting rubber identification mark away from the notch of the spring seat and install.

Fig. 10: Sliding Mounting Rubber Identification Mark From Notch

Courtesy of MAZDA MOTORS CORP.

FRONT SHOCK ABSORBER INSPECTION

1. Remove the front shock absorber. (See

FRONT SHOCK ABSORBER AND COIL SPRING

REMOVAL/INSTALLATION

.) (See

FRONT SHOCK ABSORBER AND COIL SPRING

DISASSEMBLY/ASSEMBLY

2. Inspect for damage and oil leakage.
3. Compress and extend the shock piston at least three times. Verify that the operational force does not

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION Front Suspension - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:23:19 AM

Page 6

«
...
1588
1589
1590
1591
1592
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды