Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1692

Страница: 1692 / 2589

Fig. 19: Identifying Front Airflow Mode Actuator Removal Order

Courtesy of MAZDA MOTORS CORP.

FRONT AIRFLOW MODE ACTUATOR INSPECTION

1. Connect battery positive voltage to front airflow mode actuator terminal F (or G), connect terminal G (or

F) to ground, and then verify that the front airflow mode actuator operates as shown in the table.

If the operation condition is not normal, replace the front airflow mode actuator.

FRONT AIRFLOW MODE ACTUATOR OPERATION

Fig. 20: Front Airflow Mode Actuator Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

Terminal

Front airflow mode actuator operation

B+ Ground

VENT --> DEFROSTER

Ground B+

DEFROSTER --> VENT

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:35 AM

Page 13

«
...
1690
1691
1692
1693
1694
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды