Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 641

Страница: 641 / 2589

6. Remove the PLG drive unit.
7. Install in the reverse order of removal.

Fig. 16: View Of PLG Drive Unit Connector & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

POWER LIFTGATE (PLG) CONTROL MODULE REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Trunk box (See

TRUNK BOX REMOVAL/INSTALLATION

2. Seat side box (LH) (See

SEAT SIDE BOX REMOVAL/INSTALLATION

3. Trunk end trim (See

TRUNK END TRIM REMOVAL/INSTALLATION

4. Third-row seat (See

THIRD-ROW SEAT REMOVAL/INSTALLATION

5. Third-row seat belt lower anchor installation bolt (LH) (See

THIRD-ROW SEAT BELT

REMOVAL/INSTALLATION

6. Trunk side trim (LH) (See

TRUNK SIDE TRIM REMOVAL/INSTALLATION

3. Disconnect the PLG control module connector.
4. Remove the bolts.
5. Remove the PLG control module.
6. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Doors and Liftgate - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:45:23 AM

Page 15

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды