Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 300

Страница: 300 / 2589

Fig. 250: Identifying Input Shaft And Front Planetary Gear

Courtesy of MAZDA MOTORS CORP.

45. Apply ATF to the bushing of the C3 clutch component.

46. Install the C3 clutch component to the transaxle case.

Fig. 251: Identifying C3 Clutch Component Of Transaxle Case

Courtesy of MAZDA MOTORS CORP.

NOTE:

Before installing the C3 clutch component, align the spline of the C3

clutch drive plates and the spline of the B1 brake drive plates.

NOTE:

Install the C3 clutch component so that it engages with the sun gear

drum as shown in the figure.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:17 AM

Page 137

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды