Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1722

Страница: 1722 / 2589

Rear
evaporator

temperature
sensor input

Rear evaporator

temperature sensor

Compared with
temperature

detected by rear
evaporator

temperature sensor

Refer to

temperature sensor: 2J-
B, 2P-A)

Wiring harness: short
circuit (Front climate

control unit-rear
evaporator temperature

sensor: 2J-B)

Rear evaporator
temperature sensor

Cabin
temperature

sensor input

Cabin temperature

sensor

Compared with
temperature

detected by cabin
temperature sensor

Refer to

Wiring harness:
continuity (Front

climate control unit-
cabin temperature

sensor: 2K-B, 2P-A)

Wiring harness: short
circuit (Front climate

control unit-cabin
temperature sensor:

2K-B)

Cabin temperature

sensor

Solar radiation
sensor(LH)

input

Solar radiation
sensor

Natural sunlight

shined directly on
the solar radiation

sensor

4.0

Wiring harness:

continuity (Front
climate control unit-

solar radiation sensor:
2M-C, 2B-A)

Front climate control

unit: terminal voltage

(2B)

Solar radiation sensor

Blocking light to
solar radiation

sensor

1.0 or
less

Potentiometer
input

Rear air mix
actuator

Temperature control
dial (rear side): Set

temperature at
MAX COLD

1.3

Wiring harness:

continuity, short circuit
(Front climate control

unit-rear air mix
actuator: 2N-E)

Rear air mix actuator

Front climate control

unit: terminal voltage
(2B)

Temperature control
dial (rear side): Set

temperature at
MAX HOT

4.0

Natural sunlight

shined directly on
the solar radiation

4.0

Wiring harness:

continuity (Front
climate control unit-

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:36 AM

Page 43

«
...
1720
1721
1722
1723
1724
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды