Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 709

Страница: 709 / 2589

FRONT ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION

1. When removing the right front ABS wheel-speed sensor, perform the following procedure.

1. Remove the coolant reserve tank installation bolts and move the coolant reserve tank. (See

COOLANT RESERVE TANK REMOVAL/INSTALLATION [MZI-3.7]

2. Remove the power steering reserve tank installation bolt and nut, and move the power steering

reserve tank. (See

POWER STEERING OIL PUMP REMOVAL/INSTALLATION

2. When removing the left front ABS wheel-speed sensor, perform the following procedure:

1. Remove the air cleaner case. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION

[MZI-3.7]

3. Remove in the order indicated in the table.

Fig. 16: Identifying Front ABS Wheel Speed Sensor Connector, Front ABS Wheel Speed Sensor,
Bolt & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

Power supply

(ABS motor
operation)

Battery

Voltage

Under any
condition

B+

Wiring harness

(AK- battery)

Power supply

(solenoid
operation)

Battery

Voltage

Under any
condition

B+

Wiring harness
(AL- battery)

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 16

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды