Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2449

Страница: 2449 / 2589

Courtesy of MAZDA MOTORS CORP.

WIPER AND WASHER SWITCH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the lower column cover. (See

COLUMN COVER REMOVAL/INSTALLATION

3. Put aside the upper column cover.
4. Remove in the order indicated in the table.

Fig. 19: Identifying Wiper And Washer Switch Remove/Install Components

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

WINDSHIELD WIPER AND WASHER SWITCH INSPECTION

VEHICLES WITHOUT AUTO WIPER SYSTEM

1. Verify that the continuity between the windshield wiper and washer switch is as indicated in the table.

Verify that the continuity between the windshield wiper and washer switch is as indicated in the

table.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:20 AM

Page 14

«
...
2447
2448
2449
2450
2451
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды