Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2347

Страница: 2347 / 2589

STEP

INSPECTION

ACTION

INSPECT WHEEL UNIT SIGNAL

FOR OPEN CIRCUIT

Turn the ignition switch off.

Disconnect keyless receiver and
instrument cluster connectors.

Inspect for continuity between

keyless receiver terminal D
(harness-side) and instrument

cluster terminal 1N (harness-

side).

Is there continuity?

Yes Go to the next step.

Repair or replace the wiring harness for an open circuit

between keyless receiver terminal D and instrument

cluster terminal 1N, then go to Step 4.

INSPECT WHEEL UNIT SIGNAL
FOR SHORT TO POWER

Turn the ignition switch off.

Disconnect keyless receiver and
instrument cluster connectors.

Measure the voltage between

keyless receiver terminal D
(harness-side) and ground.

Is there B+?

Yes

Repair or replace the wiring harness for a short to

power between keyless receiver terminal D and
instrument cluster terminal 1N, then go to Step 4.

Go to the next step.

INSPECT WHEEL UNIT SIGNAL

FOR SHORT TO GROUND

Turn the ignition switch off.

Disconnect keyless receiver and

instrument cluster connectors.

Inspect for continuity between
keyless receiver terminal D

(harness-side) and ground.

Is there continuity?

Yes

Repair or replace the wiring harness for a short to
ground between keyless receiver terminal D and

instrument cluster terminal 1N, then go to the next
step.

Replace keyless receiver, then go to the next step. (See

KEYLESS RECEIVER

REMOVAL/INSTALLATION

VERIFY TROUBLESHOOTING
COMPLETED

Clear the DTC from the
memory. (See

TIRE

PRESSURE MONITORING
SYSTEM (TPMS

) ONBOARD

DIAGNOSIS.)

Turn the ignition switch to the
ON position and wait for

30 s.

Yes

If the malfunction recurs, replace the instrument
cluster. (See

INSTRUMENT CLUSTER

REMOVAL/INSTALLATION

Configure the instrument cluster. (See

INSTRUMENT CLUSTER

CONFIGURATION

WHEEL UNIT

ID REGISTRATION

Go to the next step.

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION On-Board Diagnostic (Suspension) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:25:36 AM

Page 15

«
...
2345
2346
2347
2348
2349
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды