Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 384

Страница: 384 / 2589

2. Support the engine using the

SSTs.

3. Remove the No.4 engine mount bracket.

Fig. 66: Removing No.4 Engine Mount Bracket

Courtesy of MAZDA MOTORS CORP.

TRANSAXLE REMOVAL NOTE

1. Support the transaxle on a jack.
2. Remove the transaxle mounting bolts.
3. Remove the transaxle.

Fig. 67: Supporting Transaxle On Jack

Courtesy of MAZDA MOTORS CORP.

TRANSAXLE INSTALLATION NOTE

1. Set the transaxle on a jack and lift it.
2. Rotate the drive plate so that the logo mark faces upward.

NOTE:

The SST (49 E017 5A0) can be used in place of the SST (49 C017

5A0).

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 56

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды