Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1469

Страница: 1469 / 2589

Fig. 89: Identifying RH Bank Camshaft Cap Bolts Loosening Sequence

Courtesy of MAZDA MOTORS CORP.

CYLINDER HEAD REMOVAL NOTE

1. Loosen the cylinder head bolts in several passes in the order shown.

Fig. 90: Identifying Cylinder Head Bolts Loosening Sequence (Engine Front Side)

Courtesy of MAZDA MOTORS CORP.

CYLINDER HEAD INSTALLATION NOTE

1. Tighten the cylinder head bolts in the order in 6 steps in the order shown in the figure.

NOTE:

The cylinder head bolts must be replaced with new bolts. The bolts are

torque-to-yield designed and cannot be reused.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 59

«
...
1467
1468
1469
1470
1471
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды