Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2278 | Manualshive

Страница: 2278 / 2589

background image

FRONT TILT MOTOR INSPECTION

1. Disconnect the front tilt motor connector.
2. Apply battery positive voltage to the front tilt motor terminals and inspect the front tilt motor operation

z

If not as specified, replace the slide adjuster.

MOTOR OPERATION

3. Connect the front tilt motor connector.
4. Measure the front tilt motor terminal A waveform during motor operation using the oscilloscope.

VOLTAGE SPECIFICATION

z

If not as specified, replace the slide adjuster.

Fig. 15: Front Tilt Motor - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

REAR TILT MOTOR INSPECTION

1. Disconnect the rear tilt motor connector.
2. Apply battery positive voltage to the rear tilt motor terminals and inspect the rear tilt motor operation

z

If not as specified, replace the slide adjuster.

MOTOR OPERATION

Motor operation

Connection

B+ GND

Up

E

D

Down

D

E

Condition Voltage (V)

High output 4.8 or more

Low output 1.0 or less

Motor operation

Connection

B+ GND

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Seats - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:01 AM

Page 11

© 2005 Mitchell Repair Information Company, LLC.

«
...
2276
2277
2278
2279
2280
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: KC HiLiTES Страницы: 4

Бренд: Kargo Master Страницы: 6

Бренд: Ignition Страницы: 1

Бренд: JANE Страницы: 21

Retrotech RTX-68D-CHG

Бренд: Dakota Digital Страницы: 4

Бренд: Ford Страницы: 37

Бренд: Metra Electronics Страницы: 20

Бренд: Condor Страницы: 2

Бренд: Atera Страницы: 10

4500 CHASSIS CAB 2012

Бренд: RAM Страницы: 7

Бренд: EZTRUNK Страницы: 3

2014 Grand Cherokee SRT8

Бренд: Jeep Страницы: 596

Бренд: Skoda Страницы: 4

Бренд: Scion Страницы: 24

Бренд: Camecho Страницы: 2

E60-82-007-02-10

Бренд: Eibach Страницы: 3

Бренд: SNIPER Страницы: 2

Бренд: v.link Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды