Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2136 | Manualshive

Страница: 2136 / 2589

background image

DTC B266B [POWER LIFTGATE (PLG) SYSTEM]

DTC B266B - DETECTION CONDITION POSSIBLE CAUSE CHART

1

z

Disconnect the PLG control module

connector.

z

Disconnect the PLG drive unit

connector.

z

Inspect the wiring harness between
PLG control module terminal 2K and

PLG drive unit terminal E for a short
circuit to ground system.

Yes

(See

POWER LIFTGATE (PLG) DRIVE

UNIT REMOVAL/INSTALLATION

.)

Go to the next step.

No

Repair or replace the wiring harness.

Go to the next step.

2

VERIFY CORRECTION COMPLETED

z

Reconnect the disconnected connector.

z

Clear the DTC.

z

Is DTC B266A stored after

5 min or

more

have elapsed?

Yes

Replace the PLG control module.
(See

POWER LIFTGATE (PLG)

CONTROL MODULE
REMOVAL/INSTALLATION

.)

No

DTC troubleshooting completed.

DTC B266B

Rotation sensor A circuit malfunction

DETECTION

CONDITION

Rotation sensor A signal does not change

POSSIBLE

CAUSE

z

Open circuit in wiring harness between PLG control module terminal 2J and PLG
drive unit terminal F Short to power supply in wiring harness between PLG control

module terminal 2J and PLG drive unit terminal F

z

Short to GND in wiring harness between PLG control module terminal 2J and PLG
drive unit terminal F

z

Rotation sensor malfunction

z

PLG control module malfunction

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 15

© 2005 Mitchell Repair Information Company, LLC.

«
...
2134
2135
2136
2137
2138
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Daihatsu Страницы: 1718

Бренд: N-Com Страницы: 28

Titanium Series

Бренд: Fass Страницы: 13

Бренд: AA Products Страницы: 4

Бренд: Boyo Страницы: 9

Бренд: travall Страницы: 4

OPTIA hybrid 2020

Бренд: Kia Страницы: 54

Бренд: Ford Страницы: 2

Бренд: TracRac Страницы: 8

Бренд: Mitsubishi Страницы: 57

Бренд: SpeedTech Lights Страницы: 2

Бренд: Vmac Страницы: 16

Бренд: Menabo Страницы: 4

Бренд: Prime Design Страницы: 16

Бренд: Octocam Страницы: 35

Бренд: Subaru Страницы: 9

Бренд: HawksHead Страницы: 10

Бренд: Falcon Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды