Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 406

Страница: 406 / 2589

Fig. 107: Locating Transaxle Case & Bolt Holes

Courtesy of MAZDA MOTORS CORP.

12. Apply sealant to the new control valve body cover as shown in the figure.

13. Install the new control valve body cover with new seal bolts.

Tightening torque

9.8-15.7 N.m {100-160 kgf.cm, 87-138 in.lbf}

CAUTION:

Be careful that the coupler component will not become caught
between the control valve body cover and transaxle case.

Fig. 108: Applying Sealant To Control Valve Body Cover
Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 78

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды