Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1925

Страница: 1925 / 2589

2. Remove the front bumper. (See

FRONT BUMPER REMOVAL/INSTALLATION

3. Remove the front combination light. (See

FRONT COMBINATION LIGHT

REMOVAL/INSTALLATION

4. Remove in the order indicated in the table.

Fig. 11: Identifying Discharge Headlight Control Module, Connector & Screws

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

DISCHARGE HEADLIGHT SYSTEM INSPECTION

DISCHARGE HEADLIGHT INOPERATIVE

WARNING:

Incorrect servicing of the discharge headlights could result in electric

shock. Before servicing the discharge headlights, always refer to the
DISCHARGE HEADLIGHT SERVICE WARNINGS. (See DISCHARGE

HEADLIGHT SERVICE WARNINGS.)

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:05 AM

Page 9

«
...
1923
1924
1925
1926
1927
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды