Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 290

Страница: 290 / 2589

Fig. 229: Identifying One-Way Clutch Of Transaxle Case

Courtesy of MAZDA MOTORS CORP.

16. Using a flathead screwdriver, install the snap ring in the groove.

Fig. 230: Installing Snap Ring In Groove

Courtesy of MAZDA MOTORS CORP.

17. While holding the one-way clutch component, inspect that the planetary gear turns to right (clockwise)

but does not turn to left (counterclockwise).

CAUTION:

Align the opening of the snap ring with the position shown in

the figure.

CAUTION:

Do not damage the VSS.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:17 AM

Page 127

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды