Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 165

Страница: 165 / 2589

Do not apply oil or drive the vehicle immediately after installing a part applied with sealant. Leave
it for one hour or more.

Do not wash aluminum parts or rubber parts with alkaline chemicals.

Do not wash the rubber parts with white gasoline.

6. Handling ATF with care

If you spill ATF on the floor, wipe it off immediately, as it is quite slippery and dangerous.

Be sure to use JWS3309 type ATF.

Disassembly

Components

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:15 AM

Page 2

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды