Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 204

Страница: 204 / 2589

Courtesy of MAZDA MOTORS CORP.

7. Apply ATF to a new O-ring.
8. Install the O-ring to the oil pump component.

9. Turn the drive gear with flathead screwdrivers and verify it rotates smoothly.

Fig. 82: Turning Drive Gear With Flathead Screwdrivers

Courtesy of MAZDA MOTORS CORP.

B1 BRAKE PISTON DISASSEMBLY/ASSEMBLY

Components

CAUTION:

Do not damage the oil seal lip.

Fig. 81: Identifying O-Ring Of Oil Pump Component

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 41

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды