background image

 

 

Installation Instructions

 

 Ford F150 Premium Front Bumper 

Product Number: H3250, H3251, H3252 

Application: 2015-2017 Ford F150 

 

H325X_REV_A

 

         

 

SAFETY 

 

Your safety and the safety of others is very important. 

 

In order to help you make informed decisions about safety, we have provided 
installation instructions and other information.  

 

These instructions alert you to potential hazards that could hurt you or others.  

 

Please do a job safety analysis before each task to identify potential hazards for your 
situation and remove/protect against them. 

 

You must use your own good judgment, and take your time. 

Read and understand all safety precautions and instructions before installing this product. 
  

THIS PRODUCT IS FOR OFFROAD USE ONLY.  ALL LIABILITY FOR 

INSTALLATION AND USE RESTS WITH THE OWNER. 

 

CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY 

OR EQUIPMENT DAMAGE. 

 

Injury hazard 

 

Failure to observe these instructions could lead to severe injury or death. 

 

 

 

Always remove jewelry and wear eye protection. 

 

 

Always use extreme caution when jacking up a vehicle for work. Set 
emergency brake and use tire blocks.  Locate and use the vehicle 
manufacturers designated lifting points.  Use jack stands. 

 

 

Always use appropriate and adequate care in lifting components into place. 

 

 

Always ensure components will remain secure during installation and 
operation. 

 

 

Always wear safety glasses when installing this kit.  A drilling operation will 
cause flying metal chips.  Flying chips can cause serious eye injury. 

 

 

Always use extreme caution when drilling on a vehicle.  Thoroughly inspect 
the area to be drilled (on both sides of material) prior to drilling, and 
relocate any objects that may be damaged. 

 

 

Always use extreme caution when cutting and trimming during fitting. 

 

 

Always tighten all nuts and bolts securely per installation instructions. 

 

 

Always route electrical cables carefully.  Avoid moving parts, components 
that become hot and rough or sharp edges. 

 

 

Always insulate and protect all exposed wiring and electrical terminals. 

 

 

Always perform regular inspections and maintenance on mounts and 
related hardware. 

www.4x4ok.com

Содержание H3250














Отзывы: