Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 491

Страница: 491 / 2589

DTC C1446 [DSC/RSC]

DTC C1446 [DSC/RSC] DETECTION CONDITION AND POSSIBLE CAUSE

DTC C1446

Brake switch system

DETECTION

CONDITION

Brake switch ON signal is not input when the brake fluid pressure sensor signal
reaches the specified value.

Brake switch ON signal is input even if the signal from the brake fluid pressure

sensor is less than the specification.

POSSIBLE CAUSE

Open or short circuit in wiring harness between the brake switch and PCM 1T

terminal

Brake switch malfunction

Poor connection at connectors (female terminal)

2008 Mazda CX-9 Grand Touring

2008 BRAKES On-Board Diagnostic (DSC/RSC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:13 AM

Page 35

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды