background image

28-13-016-Rev1

1/10

 

LOCKN’LOAD 

TRACK MOUNTING KIT

 

    TOYOTA HILUX DUAL CAB 2015+ 

       

   2 BAR TRACK HEAVY DUTY ROOF RACK SYSTEM

•  Please read instructions carefully before installation.

•  Check the contents of kit. Contact your YAKIMA dealer if any parts appear missing or damaged.

•  Clean your roof thoroughly prior to fitting the LOCKN’LOAD Track Heavy Duty Roof Rack System.

•  Place these instructions in the vehicle’s glove box after installation is complete.

FIRST TIME INSTALLATION

1

2

KIT CONTENTS

ITEM COMPONENT

QTY

ITEM

COMPONENT

QTY

1.

Track Toyota Hilux Right Hand Side

x1

7.

Drill Bit

x1

2.

Track Toyota Hilux Left Hand Side

x1

8.

M6 Hex Screw

x8

3.

Track Nut Plate

x4

9.

End Cap Front Left & Rear Right

x2

4.

M6 Washer

x8

10.

End Cap Front Right & Rear Left

x2

5.

M6 Spring Washer

x8

11.

Rivet Gun Nozzle

x1

6.

Rivet

x14

•    Marking Pen

•    Tape Measure 

•    Masking Tape

•    Power or Cordless Drill

•    Drill Bit Stop 

•    Vacuum Cleaner 

•    Mastic Silicone Sealant

•    Fine Tooth Hacksaw
•    Hammer

•    Rubber Mallet (Optional) 

•    #2 Phillips Head Screwdriver 
•    Zinc Rich Cold Galvanising Coating

TOOLS REQUIRED:

MAX VEHICLE ROOF LOAD RATING: 100KG 

TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCES CARGO

TM

®

 

 

•    Flat Blade Screwdriver

•    10mm Open Ended Spanner 

•    13mm Socket or Spanner 

•    Rivet Gun 

•    Scissors 

•    Centre Punch 

•    Automotive Degreaser 

•    Automotive Adhesive

3

8

4

10

9

7

6

5

LEG AND BAR COMPONENTS SOLD SEPARATELY

11

Содержание LOCKN'LOAD











Отзывы: