Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1415

Страница: 1415 / 2589

1. Verify that the drive belt auto tensioner indicator mark does not exceed the maximum belt length.

If it exceeds the maximum belt length, replace the generator and A/C drive belt. (See

DRIVE

BELT REMOVAL/INSTALLATION [MZI-3.7]

2. Visually inspect the generator and A/C drive belt for damage and cracks.

If there is generator and A/C drive belt damage and cracks, replace the generator and A/C drive
belt. (See

DRIVE BELT REMOVAL/INSTALLATION [MZI-3.7]

Fig. 3: Identifying Belt Length

Courtesy of MAZDA MOTORS CORP.

POWER STEERING OIL PUMP DRIVE BELT

1. Visually inspect the power steering oil pump drive belt for damage and cracks.

If there is power steering oil pump drive belt damage and cracks, replace the power steering oil
pump drive belt. (See

DRIVE BELT REMOVAL/INSTALLATION [MZI-3.7]

GENERATOR & A/C DRIVE BELT

1. Remove the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.7]

NOTE:

When removing the generator and A/C drive belt, perform the procedure
with two people, one releasing the belt tension and the other removing the

belt.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:56 AM

Page 5

«
...
1413
1414
1415
1416
1417
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды