Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 701 | Manualshive

Страница: 701 / 2589

background image

Fig. 5: Identifying Battery Tray Bracket & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

7. Remove the nuts as shown in the figure, and move the front heater pipe.
8. Remove in the order indicated in the table.
9. Install in the reverse order of removal.

10. After installation, add brake fluid, bleed the air, and inspect for fluid leakage. (See

DSC/RSC HU AIR

BLEEDING

.) (See

AIR BLEEDING

.)

11. After installation, perform the DSC/RSC sensor initialization procedure. (See

DSC/RSC SENSOR

INITIALIZATION PROCEDURE

.)

Fig. 6: Identifying Front Heater Pipe & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 8

© 2005 Mitchell Repair Information Company, LLC.

«
...
699
700
701
702
703
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Camcar Страницы: 6

Бренд: Jeep Страницы: 25

Бренд: Jeep Страницы: 51

Бренд: Farenheit Страницы: 8

Бренд: Jeda Страницы: 8

Бренд: Jeep Страницы: 496

2013 C-Class Coupe

Бренд: Mercedes-Benz Страницы: 388

Бренд: Standby Страницы: 10

STRONGARM RVR303

Бренд: Blue Giant Страницы: 48

1973 Crown Hardtop

Бренд: Toyota Страницы: 50

PRIME DESIGN VRR-E-PM21

Бренд: Safe Fleet Страницы: 12

Бренд: Saab Страницы: 12

Бренд: Ecco Страницы: 24

Бренд: Volvo Страницы: 123

Бренд: rough country Страницы: 4

Бренд: Volvo Страницы: 197

Бренд: Mobileye Страницы: 29

Бренд: Phonocell Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды